Miller Electric Delta-Fab Uživatelský manuál

Visit our website atwww.MillerWelds.comOM-2241 209 815H2006−03ProcessesDescriptionGas Metal Arc (MIG) WeldingArc Welding Power SourceAir Carbon Arc Cu

OM-2241 Page 6Le rayonnement de l’arc du procédé de soudagegénère des rayons visibles et invisibles intenses(ultraviolets et infrarouges) susceptibles

OM-2241 Page 72-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenanceRisque D’INCENDIE OU D’EXPLO-SION.D Ne

OM-2241 Page 82-5. Principales normes de sécuritéSafety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,de Global Engineering Documents

OM-2241 Page 9SECTION 3 − INSTALLATION3-1. SpecificationsVoltage RangeAmperes Input at Rated Load Output,60 Hz, Three-PhaseRated Welding OutputVoltage

OM-2241 Page 103-3. Volt-Ampere CurvesVolt-ampere curves show mini-mum and maximum voltage andamperage output capabilities ofunit. Curves of other se

OM-2241 Page 113-4. Selecting A Location1 Lifting Eye2 Lifting ForksUse lifting eye or lifting forks tomove unit.If using lifting forks, extend forksb

OM-2241 Page 123-6. Dimensions And WeightsDimensionsDimensionsAA 30 in (762 mm) including lift eyeB 23 in (585 mm)BCC30-1/2 in (775 mm) includingstrai

OM-2241 Page 133-8. Weld Output Terminals And Selecting Cable SizesTotal Cable (Copper) Length In Weld Circuit Not Exceeding100 ft (30 m) Or Less150 f

OM-2241 Page 143-10. Remote 14 Receptacle RC8Ref. 800 166-DY Turn off power before con-necting to receptacle.1 Remote 14 Receptacle RC8Connect feeder

OM-2241 Page 153-12. Electrical Service GuideInput Voltage 230 460 575Input Amperes At Rated Output 69 34.5 27.5Max Recommended Standard Fuse Rating I

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

OM-2241 Page 163-14. Connecting Input Power 800 103-C / Ref. 801 116-A3/8 in3/8 inTools Needed:Y Installation must meet all Nationaland Local Codes −

OM-2241 Page 17SECTION 4 − OPERATION4-1. Controls209 38331 Voltage Meter2 Amperage MeterVoltmeter and ammeter display actual outputvoltage and amperag

OM-2241 Page 185-2. Fuse F1Ref. 800 101-CY Disconnect input power be-fore opening rear accessdoor.1 Fuse Holder Cover2 Fuse F1 (See Parts List ForRati

OM-2241 Page 195-4. Troubleshooting TableTrouble RemedyNo weld output; unit completelyinoperative.Place line disconnect switch in On position (see Sec

OM-2241 Page 20SECTION 6 − ELECTRICAL DIAGRAM218 521-AFigure 6-1. Circuit Diagram

OM-2241 Page 21Notes

OM-2241 Page 22SECTION 7 − PARTS LIST. Hardware is common and notavailable unless listed.803 388-B342213426785910111213171514161920212234233226 272825

OM-2241 Page 23DescriptionPartNo.Dia.Mkgs.ItemNo.QuantityFigure 7-1 Main Assembly1 +179 430 PANEL, side 2. . . . . . . . . . . . . . . . . . . . .

OM-2241 Page 24. Hardware is common and notavailable unless listed.803 389-C1234561617192021222423788910911131415121825252592726Figure 7-2 Panel, Fro

OM-2241 Page 25Figure 7-2 Panel, Front w/Components (Fig 7-1 Item 33) (continued)DescriptionPartNo.Dia.Mkgs.ItemNo.QuantityPLG2 185 626 CONNECTOR, bod

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbo

OM-2241 Page 26. Hardware is common and notavailable unless listed.1800 707-B234569107811Figure 7-4 Panel, Rear w/ComponentsDescriptionPartNo.Dia.Mkg

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 2006−01Your distributor also givesyou ...ServiceYou always get the

PRINTED IN USA © 2006 Miller Electric Mfg. Co.2006−01Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914

Notes

OM-2241 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGsom _3/05Y Warning: Protect yourself and others from injury — read and follow these pr

OM-2241 Page 2Arc rays from the welding process produce intensevisible and invisible (ultraviolet and infrared) raysthat can burn eyes and skin. Spark

OM-2241 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceFIRE OR EXPLOSION hazard.D Do not install or place unit on, over, or

OM-2241 Page 41-5. Principal Safety StandardsSafety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,from Global Engineering Documents (

OM-2241 Page 5SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATIONfre_som _3/05Y Avertissement : se protéger et protéger les autres contre le ri